[OmniOS-discuss] SAS 9305-16e HBA support in Illumos

[Schweiss, Chip]

I made the assumption that a Broadcom/LSI HBA would be supported already in
OmniOS CE r151022o.

This HBA is not loading.

Here's the 'lspci -vv' output:

02:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS3216
PCI-Express Fusion-MPT SAS-3 (rev 01)
        Subsystem: LSI Logic / Symbios Logic Device 3180
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 10
        Region 0: I/O ports at e000
        Region 1: Memory at df200000 (64-bit, non-prefetchable)
        Expansion ROM at df100000 [disabled]
        Capabilities: [50] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
SlotPowerLimit 75.000W
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
                        RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
FLReset-
                        MaxPayload 256 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
                LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM not supported,
Exit Latency L0s <2us, L1 <4us
                        ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 8GT/s, Width x8, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-,
OBFF Not Supported
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
LTR-, OBFF Disabled
                AtomicOpsCtl: ReqEn-
                LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance-
SpeedDis-
                         Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete+, EqualizationPhase1+
                         EqualizationPhase2+, EqualizationPhase3+,
LinkEqualizationRequest-
        Capabilities: [d0] Vital Product Data
                Not readable
        Capabilities: [a8] MSI: Enable- Count=1/1 Maskable+ 64bit+
                Address: 0000000000000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [c0] MSI-X: Enable- Count=96 Masked-
                Vector table: BAR=1 offset=0000e000
                PBA: BAR=1 offset=0000f000



Is this just a matter of the PCI ID getting add to mpt_sas or is there much
more work to be done for this HBA?

-Chip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://omniosce.org/ml-archive/attachments/20170830/ff35dfb5/attachment.html>